11 Ways To Fully Redesign Your Fiat 500 Replacement Key Cost

Fiat 500 Replacement Key Fob

It may be time to replace the battery if your 500 remote key fob isn't working. If you replace the battery but it isn't working it could be a problem somewhere else.

At United Locksmith, we specialize in the creation of new keys for classic cars. We have all of the tools and accessories needed to perform this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The battery for the coin cell in the key fob is likely to drain quickly when you don't utilize frequently enough. If your remote began to show signs of weakness like a loss of range and stopped working completely it is likely that the battery is dead.

The battery inside the key fob is held in place by metal clips that retain it. If the clips are not tightly secured, they could result in problems with the contact, which can stop your remote from receiving power. Use a flathead screwdriver to pry open the retaining clip and then remove the old battery. Use a battery that has the same size, voltage and specifications as the original.

The key fob can also become corroded or damaged by exposure to water. Even a brief bath in soapy water may harm the electronic chip in. Make sure your key fob is dry.

Water Damage

If your key fob isn't working properly, it could be caused by water damage. Key fobs have rubber seals to protect them from being damaged by light rain or a splash of water, however it is very important to keep your car keys out of the pool, ocean and washing machine!

The key fob contains an electronic chip which sends an electronic message to the immobilizer system of your vehicle. The chip is what allows the 500 to be locked and started. If it gets wet, however it won't function.

If you're trying to determine whether your key fob still working You can clean the internal electronics using isopropyl or electronic cleaner. However, it is probably recommended to purchase a replacement from a dealership instead of trying to fix a key fob that has been submerged in salt water.

While a replacement fob could cost a bit of money, it is a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also fix it yourself by following just a few steps. Just ensure you have the right battery type before you attempt to open your key fob. This task is more straightforward than it appears and you can find step-by-step directions online for virtually any car spare key for fiat 500 fob.

Faulty Chip

The chip located within the key fob communicates with the vehicle's immobiliser to ensure that your car is only able to start when the correct key is used. If the chip is damaged, or damaged in any way it will not start.

A chip that is damaged can happen due to several reasons, but the most common cause is water damage or the battery being dead. It is best to hand over the job to a professional locksmith, who can replace the chip in a short time and at a a reasonable price.

If your key fob stops functioning after exposure to clean tap water or rain, take out the battery and clean the electronic component with a towel to ensure it is fully dry before putting it back into. If the key fob still does not work it's probably to be a damaged chip and must be replaced.

Some people will visit their dealer in order to get a new fiat 500 abarth key fob. However, this can be expensive. United Locksmith is the best choice if you want your fiat ducato remote key replacement key fob repaired at a reasonable cost. We have the tools and expertise needed to repair your fiat 500 key fob replacement key fob in a quick and professional manner.

Faulty Receiver Module

fiat 500 keys key fobs send an electrical signal to the vehicle, which will unlock and lock doors (and start the car for those with an automatic transmission) up to 50 feet. There are several reasons why the fob might not function. This could be due to a dead coin battery, water damage, worn buttons and a receiver module issue, and signal interference or a malfunctioning electronic chip.

If the fob is in a pocket which has suffered extreme trauma (such as being dropped onto a hard floor or being washed in a washing machine) it might not be able to communicate with the Body Control Module (BCM) of the vehicle. The BCM is a security system that can only accept signals from genuine original keys.

It is necessary to replace the fob in case this occurs. A professional locksmith can take care of all aspects of the replacement process, including programming a new one for the 500. In fact, they could provide you with a clone key that works just like the original fob (and costs less than the price).