15 Shocking Facts About Peugeot Keys That You've Never Heard Of

Peugeot 208 Key Replacement

peugeot 107 spare key 208 key replacement is best left to experienced auto locksmiths with the right tools and know-how. They will be able to create and program new keys much quicker than a dealership and at a lower cost.

A dead coin battery is the most likely cause the reason your key-fob stops locking or unlocking the doors. There are other reasons that the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as stopping it from starting the engine. If this is the scenario, you'll need apply the backup starting technique that is detailed in the owner's manual for your vehicle.

The spark plugs could also be worn out. The spark plugs light the fuel to start the engine. They have a limited life span. If they aren't utilized enough they will eventually fail.

There is a straightforward solution to this problem. The best solution is to test the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts, then it's time to replace it. It is also important to clean the contacts of the battery if it has corrosion. You can do this by lifting the rubber covers that protect the two battery terminals and using a wire brush to remove any corroded components of the battery. Then, you must reconnect the positive pole cables to the negative.

Water Damage

If your 208 will not start and the battery hasn't been replaced, you must check the spark plugs. It is possible that they're overly dirty, causing them not to spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only the correct key can turn the engine. If the chip inside the peugeot key fob programming key is damaged then it will not send the correct signal to the vehicle.

This is a typical issue that is caused by water damage. This is a common problem in areas with colder temperatures where the vehicle has been exposed to snow or rain. In this case, you need to contact a reliable locksmith who has the tools and equipment needed to change the key's programming. They will also have the latest technological know-how and the equipment required to make a Peugeot 208 smart key. The process shouldn't last more than 15 minutes.

Contacts with the battery may be damaged.

peugeot 107 remote key replaced the old transponder chips using a new type that uses electronic components mounted on a circuit board. This new technology works great when it's new, however, over time, the circuit boards start to wear out and stop functioning correctly.

This could stop the immobiliser chip from working, so your car won't start. Contact a Peugeot specialist or a locksmith, if this is the situation.

Another issue that is common is when the battery of the key fob gets depleted, which causes the key blade to stop feeding into the lock. A car locksmith will replace the battery and then cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden rain or accidentally washing it, it could be due to a faulty receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.

Rubber seals on the key fob keep water from reaching its electronic chip. The chip can be damaged by water when exposed to water for a long period of. Submerging the key fob in ocean water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working You'll need the module replaced. This can only be done by a skilled auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct programming for the start of the engine. This is why you should only be able to trust a professional Peugeot locksmith with the task of designing and programming an alternative.

Computer on board is not working properly

The on-board computer inside your Peugeot is responsible for a number of the systems within the car, from power windows to airbags. The on-board computer displays the code when something goes wrong. The code is stored within the system until the issue is fixed. Most often, this involves replacing the on-board computer.

One of the most frequent causes of the airbag light flashing is loose or corroded connectors in the airbag sensor. This can occur due to wear and tear, aging or exposure to salt and moisture. It is imperative to have this issue resolved as soon as possible, since an airbag that is not functioning properly could be risky in the event of an accident.

If your Peugeot is showing a card not detected error, the battery inside the key fob might be dead or weak. This will stop the key fob sending a signal to disarm the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If this doesn't work it is likely that the battery will need replacing.